Spa Repair Services — Heaters, Pumps, Leaks & More

Heater Repair

Spa won't heat, tripping breaker, error codes.

Pump & Motor

Loud bearings, leaking seals, weak circulation.

Leak Detection

Pressure-test plumbing, dye-test fittings, repair.

Jets & Plumbing

Weak jets, no air, replace internals, rebuild manifolds.

Control Panels

Topside not responding, error codes, board replacement.

Drain, Clean & Refill

Quarterly deep clean, line flush, chemistry rebalance.

Covers & Lifters

Custom covers, cover lifters, surround skirting.

Salt & Ozone

Salt cell replacement, ozone install, frog/inline systems.

01 · Heater Repair & Replacement

Cold spa? It's almost always one of these five things.

Hot tub heaters fail in predictable ways. We carry replacement elements, sensors, high-limit switches, and pressure switches on every truck so most no-heat calls are fixed in a single visit.

Heater element burned out — corroded contacts, scaled element, or electrical short
High-limit / hi-limit switch tripped — usually a flow problem, not the switch itself
Pressure switch failure — won't sense flow, heater locks out (FLO error)
Temp sensor drift — reading wrong, heater cycles incorrectly (OH error)
Heat pump issues — refrigerant, fan motor, contactor (we're EPA 608 certified)

Diagnose my heater →

02 · Pump & Motor Service

Loud spa? Your pump bearings are gone.

Spa pumps run thousands of hours per year. Bearings wear out, seals leak, capacitors fail. We diagnose the failure mode and fix the actual problem — not just swap the whole pump.

Bearing replacement — extends life of an otherwise-good motor
Seal kit replacement — stops drips at the wet-end, prevents motor damage
Wet-end / impeller swap — restores flow when impeller is cracked or eroded
Full pump replacement — Waterway, Aqua-Flo, Gecko, ITT pump in stock or 24-hr turn
Capacitor / motor diagnostic — humming-but-not-spinning is a $40 capacitor 80% of the time

Pump diagnostic →

Technician using a power drill on spa equipment

03 · Leak Detection & Repair

Water on the pad? We find leaks the right way.

Most "spa techs" guess at leaks. We pressure-test the plumbing system, dye-test fittings, and isolate the leak source before opening anything up. No exploratory destruction.

Plumbing pressure test — isolate jet lines, pump unions, manifold leaks
Dye testing — pinpoint shell cracks, jet body leaks, drain fitting failures
Heater housing & pump seals — drips at the equipment bay are the most common
Shell leak repair — fiberglass / acrylic patch, jet rebuild
Slab/foundation leaks — when plumbing has cracked under the spa, we'll quote the rebuild honestly

Find my leak →

Foaming hot tub water during pressure test

04 · Jets, Air & Plumbing

Weak jets, no air, missing pieces.

Spa jets get calcium-locked, lose their internals, or break off entirely. Plumbing manifolds crack with age. We rebuild what's broken and swap-in OEM-grade replacements.

Jet internal replacement — Waterway, CMP, Pentair, HydroAir interchangeable parts
Diverter valve repair — sticky, leaking, or broken handles
Air injector / venturi service — restore the airflow that creates the bubble effect
Plumbing manifold repair — crack repair, full manifold replacement
Whole-system flow balancing — make sure every jet is putting out properly

Restore my jets →

05 · Control Panels & Electronics

Topside dead, error codes, no display.

Modern spas have circuit boards from a half-dozen manufacturers. We carry common boards in stock for Balboa, Gecko, and Hydro-Quip — and can decode the error code on every major brand.

Topside controller repair / replacement — the most common point of failure
Main control board diagnostic — Balboa BP, Gecko in.YE/in.YT, Hydro-Quip Eco-3
GFCI / disconnect troubleshooting — nuisance trips, no-power conditions
Sensor replacement — temp sensors, flow sensors, pressure sensors
Wi-Fi module install — Balboa BWA, Gecko in.touch 2 — control your spa from anywhere

Decode my error →

Spa technician working on electrical control panel

06 · Drain, Clean & Refill

Recommended every 3–4 months. Most owners forget.

Your spa water has a lifespan. After ~4 months of use, total dissolved solids climb past the point that sanitizer can keep up. A proper drain & clean is the single best thing you can do for your spa's longevity.

Full drain — removes all old water, including what's hiding in the plumbing
Line flush — biofilm cleaner pushed through the plumbing for 30+ minutes
Shell deep clean — surface treatment, jet cleaning, scumline removal
Filter clean or replace — chemical soak or new cartridge
Refill & rebalance — fresh water, full chemistry start-up to your set point

See maintenance plans →

Gloved hand performing spa water chemistry test

Also available

Covers, salt cells, ozone, and more.

Custom Spa Covers

3" or 4" thick, standard or premium tapered. We measure on-site for an exact fit. Lead time 2–3 weeks. Old cover hauled away free.

Cover Lifters

Coverlift, Cover Valet, UltraLift — installed and tested. Most lifters install in under an hour.

Salt Systems & Ozone

Salt cell replacement (FreshWater Salt, Hot Spring), ozone module install, FROG inline cartridges, UV systems.

Spa Steps & Surrounds

Replacement steps, surround skirting panels, deck-mounted handrails. Compatible with most major brands.

New Equipment Installs

Replacing your entire equipment pack? We swap heaters, packs, plumbing, and pumps as a unit. Honest quotes against a new spa.

Spa Moves & Reinstalls

Disconnecting, moving across town, reconnecting. Includes electrical, plumbing, and start-up. Quote based on access.

Spa repair services, done right.